I have a power line model PLI 190 - 3 Isolator in my 1992 Grandvilla. I am replacing bad batteries and believe my isolator is shot. I have read all (most) posts regarding the isolator and am pretty convinced I need a new one.
I have removed the house batteries and just have the starter battery in place. The starter battery is only connected to the starter and the isolator. Without a house battery all my 12 volt house fixtures still work - i.e. lights, 12 volt tv outlet, water pump. This was my first indicator that I had a problem. I tested the isolator and with no house battery I got a 12.5 volt reading from the house lug. I also got a 12 .6 from the start battery lug. Does this sound like a bad isolator. Just double checking before I purchase another one.
Thanks
Howard Reinhardt
The purpose of a isolator is to "isolate" the start battery from the house systems, so you can't discharge it to the point where it won't start the coach. If your 12 volt house circuits are (apparently) being powered off the start battery, and there are no other batteries present, AND you are not powering the charger/converter by being plugged in or running your generator, then I would say "Yes" your isolator is toast. Just my opinion, but I don't see any other explanation. Wait for other "experts" to weigh in, as I'm sure they will.
Thanks cajk - No other batteries present, not plugged in, and not running generator. Left me with no explanation either.
If you are replacing batteries, and your coach still has the original factory installed charger/converter, then you should seriously consider getting a new "smart" replacement. It will add years to the life of your new batteries, and contribute greatly to your "peace of mind". Search the forum for product recommendations.
I would also check the boost solenoid as it may have the contacts stuck together which would be keeping the house activated through it. Easy to check, just remove one of the large wires on the solenoid and see if the house is still activated. You could also do that with the isolator as well. How about solar.
We we bought our U300, we went to a wedding and had the roof fan on all day. That night, both house and engine batteries were dead. I just jumped it to get it going but when we got home, I started looking at the schematic and discovered the isolator had been wired incorrectly. Super easy to make a mistake when changing isolators. After checking all the cables and their destinations against the electrical schematic, I recommend using a label machine to put the correct code and where the cable goes/comes from. There is a code on the cable but in this location, it usually fades so you can't read it.
Also possible as noted above, that the boost solenoid has failed.
I have the electrical schematic for '93 U300/U280 I can email. It may be close enough to help if you don't have yours.
Pierce
A boost solenoid stuck on is a more likely fault than a shorted diode in the isolator, they usually open on failure.
See, I told you you would get good advice from the more experienced members. I'm still a rookie at this stuff.
I have a question about how you left your battery cables when you removed the coach batteries. On my wiring diagram, the positive post of one of the coach batteries has 3 cables attached, labeled B3, B4 and B11. If your setup is the same, then I'm wondering if you left those 3 cables connected to each other. If so, then that is how the boost solenoid stuck in the "closed" position would be able to supply power to all the coach circuits. A stuck boost solenoid would also explain why you got the same voltage reading on both battery posts on the isolator. I think I'm gonna retract my initial opinion, and throw in with Ron's diagnosis. Your isolator may be just fine.
I would do what Ron suggested - remove the big cable from the "coach battery" post on the isolator. Then check voltage on both posts of of the boost solenoid. If you get the same reading (start battery voltage) on both posts, the solenoid is bad.
Thanks all. Cajk - I have replaced the converter with a progressive dynamics intellipower 9100 series, with charge wizard. Old one died a couple of years ago.
Red Tractor - I think you may have something there. I used a wire to check the solenoid and did not get a clicking, so possibly the contacts are stuck. Will do the testing as mentioned, thanks.
Good suggestion Pierce. Would also love a copy of the electrical schematic - hjrein@aol.com. Thanks.
Didn't think of the boost solenoid first - now its on the top of my list. Thanks Tom
Appreciate the help - got some checking to do tomorrow.