Driving this weekend to St. Augustine from St. Petersburg, and back and on several occasions heard what sounded like a power steering pump whine or growl as I was making turns at a slow speeds. Any ideas?
I have usually associated that with air getting into the system. How's the reservoir level?
I checked and it was just below the fill when hot line, I wouldn't think that would make much of a difference. I hope that you say I may be wrong!
Rick,
Unless your hearing is a LOT better than mine, I don't think you could actually hear the power steering pump from 36 feet away with the big engine running. BUT, you could hear something in the front end that sounds like that noise... I'm guessing it is more likely something in the steering mechanism, steering linkage, or in the front suspension. Perhaps a dry suspension joint that needs some grease? When was the last time your coach was lubed? Have you checked the steering box to see if it is leaking? How long since you changed the power steering fluid and filters?
Does this only happen in tight turns? Could it be a tire rubbing on the air bag flange? This is not uncommon, especially if you just replaced the front tires.
I occasionally get some noise from my steering column that sounds like groaning. It is intermittent, and doesn't happen often enough to get me off my rear and figure out what is causing it. I suspect a dry rubber seal or dust boot or something like that...
Sorry...that's all I've got.
Well I called Kieth Riesch At MOT and the first thing that he asked was, have you bought new tires? The answer was yes, just last week. He then said I believe that I know what the problem is. The new tires today are about 1/4 " larger than before and when you make a right turn the tire barely rubs the bottom of the airbag mount. Checked it out and sure enough the paint was rubbed off where the tire barely rubs. I asked what to do, and Kieth said that if the noise doesn't bother you, don't worry and just let it be. The noise does not bother me now that I know what the cause is, so I let be.
Rick,
DO check ride height. Easy to do. And, if low it will allow more tire/air bag support contact.
Rick, what brand and size tires did you buy, that are rubbing the airbag mounting?
Michelin 275 x 22.5
Have not changed a air bag yet but I read that when you do the bottom and top plates can be shimmied/positioned somewhat,
this being true may be a solution,any ideas on this? Just put the rear fronts as far back as you can,sounds like even an eigth of an inch would help.
I replaced my airbags a couple of years ago, too late for that. Any way I am not taking any action to change it, as it seems there is no harm being done, other than an occasional sound when making a right hand turn.
when did you last change hydraulic fluid and filters? I had same noise before oil and filter change.
Hmmm, Don't understand how the bottom airbag support clearance changes with ride height.
Brett I brought the ride height valve up with Keith at MOT and he said that the airbag support bracket moves with the ride height valve and will not make a difference.
Apologies to both of you-- I did not trigger on the fact that it was the LOWER bracket that the tire was hitting.
You are correct, ride height has no effect on the LOWER bracket clearance.
As I recall, some have filed off/sawed off some of the lower bracket (not getting into any area that would weaken the bag support).
So, the question would be: is the area of contact necessary for bag support-- of not consider hacksawing a little off.
Hopefully others who have encountered the same issue will chime in.
I thought of doing something like that, however it is little reward for me to do it the rub hurts nothing, and if you cut or file you stand a chance of hurting the bag or perhaps leaving a bur or rough edge which could do more damage.
Rick,
Thinking cap back on.
How much cut angle would you loose to narrow it to where the tire just did not contact the bracket.
It is not that difficult to adjust cut angle. So, if all you would loose is a couple of degrees, let us know and we can give you the procedure for setting cut angles.
With the coach raised up to the limit, the air bag is far enough away from the plate to use a 4" grinder without hitting rubber. Looking at mine the rubber would not make contact with the area of the plate that was ground when deflated.