Foretravel Motorhome Forums => Foretravel Discussions => Topic started by: gracerace on November 15, 2018, 08:34:51 pm
Title: 6 pack rebuild
Post by: gracerace on November 15, 2018, 08:34:51 pm
I think it's easier in the long run to just pull the 6 pack unit, and do it on the bench. I know there has been a lot of discussion on this in the past.
I have been fighting a L/F a major air leak since last winter when I replaced a bad travel solenoid. I did that one while laying on my back in the Parker desert.........Way out where we had just spent the last couple of nights 'Howeling at the Moon" with our neighbor at home, and good friend Kelly Hughes
Anyway,while the engine was out this summer, I rebuilt 4 of the front valve's, and installed another new complete HWH travel solenoid to match the other one.
I used the untested ones which didn't work..... (They are NOT Tom Mc Clouds)....His work awesome
These are the one's that DID NOT work: Inventories in Stock by Oemsurplus911.com (http://www.oemsurplus911.com/skinner/skinner_parts.htm)
Once I got the coach going with the new engine, the leak was worse, I believe because of the untested ones mentioned above.So I ordered the one's from Tom, and installed those. They look and smell like the HWH ones, but I still had an issues.
Being frustrated, I bought a couple of manual shut off valves from the hardware store to narrow down the issue.Make a short story long, I narrowed it down to the left solenoids.So I decided to just yank the manifold off, and set it up to bench test it with air.
So what did I find you asked. I guess I dropped the 'O'ring in the plunger, so it was leaking from there. Funny thing is, I soaped the heck out of it several times, it didn't show. So another good reason to pull the manifold.
Going to do the rear 6 pack this way.I rigged up a gauge and shut off valve, so I can bench test them afterwards. I also marked everything with some masking tape to make it easier. I'll remove it when done Chris
Title: Re: 6 pack rebuild
Post by: Chuck & Jeannie on November 15, 2018, 09:12:21 pm
You might check the O-rings on the check valves and the retaining plugs while you are at it. They were in good shape on my front 6-pack, but I installed new ones anyway. Peace of mind thing... O-ring sizes listed in post linked below:
Working On My Six Pack (http://www.foreforums.com/index.php?topic=27491.msg225369#msg225369)
Title: Re: 6 pack rebuild
Post by: krush on November 15, 2018, 09:31:00 pm
My low pressure sensor doesn't work on my rear 6pack. It will never stop "venting" air, even when none is left in the bags and it's sitting on the stops. Anybody ever mess with the pressure switch?
Title: Re: 6 pack rebuild
Post by: Chuck & Jeannie on November 15, 2018, 10:13:28 pm
My low pressure sensor doesn't work on my rear 6pack. It will never stop "venting" air, even when none is left in the bags and it's sitting on the stops. Anybody ever mess with the pressure switch?
I don't understand your question. The pressure switch on the rear 6-pack does not "vent air". It is a simple pressure sensor - enclosed electrical contacts that are either open or closed, depending on what pressure it sees. See a better explanation below:
You might check the O-rings on the check valves and the retaining plugs while you are at it. They were in good shape on my front 6-pack, but I installed new ones anyway. Peace of mind thing... O-ring sizes listed in post linked below:
Working On My Six Pack (http://www.foreforums.com/index.php?topic=27491.msg225369#msg225369)
Good info, thanks. I did take them apart, cleaned & checked them. Also replaced both pressure switches.
Title: Re: 6 pack rebuild
Post by: krush on November 15, 2018, 10:55:34 pm
I don't understand your question. The pressure switch on the rear 6-pack does not "vent air". It is a simple pressure sensor - enclosed electrical contacts that are either open or closed, depending on what pressure it sees. See a better explanation below:
Parts diagram with HWH part number for 85 PSI pressure switch:
http://www.hwhcorp.com/mr053300.pdf
Thanks for the links and info. I'll look at the pressure switch and maybe replace it. Mine is stuck and not working.
Edit: I think it may be this drawing or one like this...20 psi pressure switch. It's in the manifold assembly to maintain at least 20psi in the air bags: https://www.hwhcorp.com/mr053325.pdf
Title: Re: 6 pack rebuild
Post by: Chuck & Jeannie on November 15, 2018, 11:47:28 pm
Title: Re: 6 pack rebuild
Post by: encantotom on November 16, 2018, 10:10:55 am
i have had those pressure switches leak. when they do, i just take them out and plug the hole until i find one. i have had to replace the rear one and one of the front ones. each coach manufacturer seems to put a slightly different pressure reading ones on. give or take 10 psi or so.
they are in my mind nice to have but not totally necessary. when they are disconnected they are in a state that still allows the system to work. what they do is tell you if you have enough air in the system to float the bags, or that you are completely low on air. if you have them out or disconnected, you just have to be aware of your air pressure situation.
tom
Title: Re: 6 pack rebuild
Post by: Chuck & Jeannie on November 16, 2018, 10:25:37 am
Reiterating what Chris said:
FRONT MANIFOLD: TWO 10 PSI SWITCHES REAR MANIFOLD: ONE 85 PSI SWITCH
The front pressure switches are easy to find. See the link posted above (Reply #6). The 85 PSI switch is another matter entirely...
It is a funny coincidence that Tom just posted (above) because I was just reading one of his posts on another forum from 7 years ago! Seems this pesky 85 PSI switch has been a thorn in the side of RV owners for many years. Here is what my Google search turned up.
First, the HWH part number is RAP90570, and (if available) it is probably pretty pricey from them, but I didn't actually call to get a quote.
Searching online for the HWH part number, I found these pertinent discussions:
what is this thing on the rear 6 pack? - Luxury Coach Lifestyles (http://www.luxurycoachlifestyle.com/forums/showthread.php?t=1942) (Tom's old post)
Where can I get Nason pressure switches (for HWH) at a discount price? -... (http://www.irv2.com/forums/f258/where-can-i-get-nason-pressure-switches-for-hwh-at-a-discount-price-391469.html)
Those three threads led me to these sources for a substitute (but not exact duplicate) 85 PSI switch:
Presur Swtch,Stndrd,51 to 90 psi,SPST-NC HONEYWELL 76064-B00000600-01 | eBay (https://www.ebay.com/itm/Presur-Swtch-Stndrd-51-to-90-psi-SPST-NC-HONEYWELL-76064-B00000600-01/221508486766?epid=1601602030&hash=item3392ef466e:g:648AAOSwU1FaCehR:sc:ShippingMethodExpress!83814!US!-1:rk:4:pf:0)
FRONT MANIFOLD: TWO 10 PSI SWITCHES REAR MANIFOLD: ONE 85 PSI SWITCH
The front pressure switches are easy to find. See the link posted above (Reply #6). The 85 PSI switch is another matter entirely...
It is a funny coincidence that Tom just posted (above) because I was just reading one of his posts on another forum from 7 years ago! Seems this pesky 85 PSI switch has been a thorn in the side of RV owners for many years. Here is what my Google search turned up.
First, the HWH part number is RAP90570, and (if available) it is probably pretty pricey from them, but I didn't actually call to get a quote.
Searching online for the HWH part number, I found these pertinent discussions:
what is this thing on the rear 6 pack? - Luxury Coach Lifestyles (http://www.luxurycoachlifestyle.com/forums/showthread.php?t=1942) (Tom's old post)
Where can I get Nason pressure switches (for HWH) at a discount price? -... (http://www.irv2.com/forums/f258/where-can-i-get-nason-pressure-switches-for-hwh-at-a-discount-price-391469.html)
Those three threads led me to these sources for a substitute (but not exact duplicate) 85 PSI switch:
Thanks Chuck for expanding my comment. I had just waken up, planned to come back and post links to the place to purchase them. But you did it for me :D
I went back and looked at your rebuild. Very nice professional job. I loved the way you stamped the hose numbers on the block.Those push on fittings work nice. I use them on my race car for air activated stuff.I probably should have changed mine, but just going to re-install it today. I need to move the coach.
Thanks for all your input. I post for the purpose of archiving stuff, for future help for other's. Others like yourself, have helped me immensely with their real world experience.
Cheers Chris
Title: Re: 6 pack rebuild
Post by: Chuck & Jeannie on November 16, 2018, 11:36:30 am
Thanks for all your input. I post for the purpose of archiving stuff, for future help for other's.
Yer Welcome. I actually post mostly for my OWN benefit, to help ME remember exactly what I've done (and when) to our coach. Senility Sucks! 8)
Title: Re: 6 pack rebuild
Post by: gracerace on November 17, 2018, 10:58:35 am
Woo Woo.....Success!
Did not drop even 1/8" at every corner in the last 24 hrs. Auto level off
Title: Re: 6 pack rebuild
Post by: gracerace on November 18, 2018, 05:37:15 pm
36 hours, not 1/6th inch drop at any corner. So far 12 psi out of both tanks. All the work of fixing the multi leaks at the tanks paid off. I never really got a good test, because the front 6 pack was giving me grief.
*** Auto level off***
Title: Re: 6 pack rebuild
Post by: wolfe10 on November 18, 2018, 05:38:06 pm
Good news. Your work paid off.
Title: Re: 6 pack rebuild
Post by: gracerace on November 18, 2018, 05:44:55 pm
Thanks Brett. I think I'll leave the rear 6 pack alone. If it ain't broke don't fix it. I actually replaced 2 kits back there last year.The raise was bad, but it lowered when it sat. I would roll out of bed in the morning.kind of tricked me to find the issue. I did order a new rear pressure switch, I am going to do that. It looks crusty. Chris
Title: Re: 6 pack rebuild
Post by: gracerace on November 19, 2018, 12:49:28 pm
DONE.... Calculates out to 1 PSI per hour loss in each tank. Not even going to try and find that, even if I could. On to the last minor project for now Chris
Title: Re: 6 pack rebuild
Post by: Chuck & Jeannie on November 20, 2018, 09:34:43 pm
Thought I'd tack a few photos on the end of this thread, since they pertain to the same topic...
In Reply #11 I listed 3 possible sources for substitute 85 PSI pressure switches that could be used on the rear HWH 6-pack manifold. I decided to order one of them, to put away in my spare parts drawer for a rainy day. I picked the 3rd of the three options listed, just because it looked kinda interesting. Switch arrived today, and it appears to me to be a high quality component. It is heavy - about the weight of a good 1" hex socket. Chrome plated or stainless steel - not sure which - to resist corrosion. Includes a heavy duty rubber boot to cover the two wiring contacts after the wires are attached. The boot should help the switch live a long life in the dirty, greasy and sometimes wet environment under the coach.
The switch is adjusted by inserting a Allen wrench into a socket screw between the wiring contacts. It is supposed to come set for 85 PSI. I will probably do a bench test to confirm the setting, and will report back later with the results.
After I got the switch in hand, I did a Google search for the ID info etched on the side, and got a lot of hits, most of them at cheaper prices than the link I posted. Looks like most of them are made in China. I don't know if they are all selling the same switch, or if some are rip-off copies. Caveat emptor.
Title: Re: 6 pack rebuild
Post by: gracerace on November 27, 2018, 03:24:20 pm