We have the Atwood Hydroflame 8535 III in our 1995 U300.
Turned it on the other day, the blower comes on but it never lights.
The back furnace works fine.
Has anyone had the same problem?
What are some things we should check?
Thanks, Susan
Have you opened the outside door and cover? Check for obstructions in the exhaust and blower area? Loose connections? Also the sail switch could be sticking.
The trouble shooting guide in the service manual contains a list of things to check.
https://rvpartsexpress.com/wp-content/uploads/2019/01/Atwood-Hydroflame-service-and-parts-guide.pdf
Inside that round black plastic cover* is a switch known as the sail switch. It rises on the air flow closing a micro switch. It's job is to make sure there is enough air flowing through the heat exchanger to prevent it from over heating, that and enough combustion air. While you're in there make sure the fan turns freely.
You'll appreciate having a magnetic sheet metal screw driver. Check the size with a socket before heading to Lowes or Home Depot. ICRS.
First, how far into the "run" cycle do you get--
Fan on?
Ignitor clicking? If so, for how long?
Smell propane in the exhaust?
As already posted, if the SAIL SWITCH is not closed (due to insufficient air flow) nothing other than fan will happen.
Have you had the basement door open that is right below the furnace? Whether you have or not make sure your coach has the door switch that controls the furnace. If equipped check this to see if it is working properly.
Mike
Bob is having a friend that has a heating and cooling business come look at it tomorrow.
He's pretty sure it is a problem with the sail switch because it doesn't even try to lite.
The blower runs great, just blows out cold air.
I'll post again tomorrow after his friend comes over and let everyone know what he determines.
Thanks
Susan
Also check all wiring connections. I had the same problem and found a loose connection. As soon as I tightened it up the furnace came on.
Susan, if it's appropriate let Bob know that there is an aftermarket upgrade for the control board by Dinosaur electronics. The original control board will run your batteries flat if the furnace doesn't light and you're not home. The Dinosaur board will try three times before turning off the blower, waiting one hour and trying again before locking down.
Having dry camped in New England, and having mis-managed my battery state of charge, I can tell you that having the furnace re-start at 3:00 AM one more time allows for a full nights sleep.
My love for my cedar wardrobe in the hall? Second is the generator start switch in the bedroom.
Art
Hmmm. Remote possibility but worth a try. Swap thermostats with the bedroom one.
Last month our bedroom thermostat would turn on, the furnace would go thru the purge cycle, then the igniter lit the propane and I could hear the flame go on and after precisely 10 seconds flame went out and purge/cool down cycle. Then shutoff. Repeat after a bit.
I ended up buying a universal thermostat from our RV dealer for about $26+ tax. Now the furnace works perfect.
To eliminate the control board swap it with the other furnace.
Unplug and reconnect all connections to wipe the contacts. Probably would do that first.
Furnace guy didn't come. Can anyone tell me where the sail switch is located. Do we have to take the whole furnace out to check it. Can't find a diagram online.
Thanks. Susan
Open the white metal cover. Drop down the flat black plastic panel (has the wiring diagram glued to it). You'll see a rounded black plastic cover. The sail switch is mounted to the underside of rounded cover.
Photo below of my furnace with all the guts removed. See the sail switch on the black rounded cover (upper left in photo)?
Video showing diagnosis of "no light" due to dirty sail switch (different model furnace but same principle as yours):
https://www.youtube.com/watch?v=-g3_Y7MqChE
Thanks so much, took off rounded cover, cleaned sail switch and it fired right up
Susan
Congratulations. Believe it or not you can remove the fan motor and replace it through that opening. Should it ever become necessary.
Good job Chuck........... photos always help,
Susan should sleep warm tonight!