Skip to main content ↑ ↓
Topic: Power Tech Generator Oil Change? (Read 3099 times) previous topic - next topic

Power Tech Generator Oil Change?

OK.  I have all of the items necessary for the oil change and the air filter change.

Does the genset slide out for the service?  If so,how?  I cannot see how to get it to pull out. I see the oil pan screw but it would pour out all over the rubber floor and there is not enough room for a catch pan without it pulled out.

(1996 U320)
Fred H.
1996 Foretravel U320 4000 Build #4993 (Previous motorhomes 1985 Airstream 345, 1977 Argosy 20)
Sevierville, TN
ViewRVs.com

Re: Power Tech Generator Oil Change?

Reply #1 –
If I remember correctly ... I loosened up the drain bolt and when it was draining half way good with the bolt still installed I went inside and let it drain.. Made a big mess when I tried to remove the bolt and the pressure pushed the oil out to fast and was hitting the pan and getting everywhere.

Re: Power Tech Generator Oil Change?

Reply #2 –
How do I release the slide tray so the gen set slides out? I need to get it rolled out so I can even get a pan underneath.
Fred H.
1996 Foretravel U320 4000 Build #4993 (Previous motorhomes 1985 Airstream 345, 1977 Argosy 20)
Sevierville, TN
ViewRVs.com

Re: Power Tech Generator Oil Change?

Reply #3 –
There is a 1/2" bolt's on each side, lower front on the tracks. Pull those, it will slide out
Chris and Tammy White  CDA Idaho
Previous owners 1997 U295 36' 3126 Cat 300 HP Build # 4998
Former Foretravel tech & RVIA certified tech
Former owner Custom Satellite home/RV satellites 
Former owner Vans LTD  van conversions
Unemployed, panhandler, drag racer NHRA #6348

Re: Power Tech Generator Oil Change?

Reply #4 –
My bolts are either 1/4 or 5/16 that's a lot smaller than 1/2.
Toby a 94 u280
Cummins 8.3
6 speed Allison
Exhaust brake


Adopted by Derek and Annabelle

Re: Power Tech Generator Oil Change?

Reply #5 –
Maybe a 1/2 inch wrench as our 98 had 5/16 inch bolts holding the gen in place in the rails.
previous 1984 35 ft ORED 250 HP 3208 Cat       
previous 1998 40 ft U295 CAI 325 hp Cummins
previous 2003 40 Ft u320 build #6140 450 Cummins M11.                                                         
1999 Mazda Miata
Ron, Nancy, Tipper the cat, Max The dog
1997 U 270 36 ft build number 5174 8.3 Cummins

Re: Power Tech Generator Oil Change?

Reply #6 –
Most likely you will have to disconnect the exhaust pipe before pulling the genny forward. I have a 01 and have to do that if I want to move the genny.
Jon Ohman
2001 U320 36'
Build #5809

Re: Power Tech Generator Oil Change?

Reply #7 –
Here's a photo showing the two bolts that must be removed.
jor
93 225
95 300
97 270
99 320

Re: Power Tech Generator Oil Change?

Reply #8 –
And the exhaust.
Speedbird 1.
2001 U320 Build #5865
Daihatsu Rocky Toad
VW Touareg
'82 F100 Stepside
Beech' Debonair

Re: Power Tech Generator Oil Change?

Reply #9 –
If this is a four cylinder then it probably won't pull out. I cut a partial circle out of the rubber floor just under the drain and let it go. Leave a flap so you can push the flap back in. Been doing OK for a few years.
Larry
1996 U295 36'
Build # 4805
Actually we sold it but just like to lurk

Re: Power Tech Generator Oil Change?

Reply #10 –
The four cylinder Kubota on my '95 U320 pulled out for service without disconnecting anything. Just the two bolts on the track.
John Duld
1995 U320C SE 40'

Re: Power Tech Generator Oil Change?

Reply #11 –
Thanks. Those were the bolts! I did get it out and changed the oil, oil filter, fuel filter, and air filter. My NAPA had all of the parts.

The oil was REALLY black. The PO claimed it was changed at 1,315 hours. It is at 1,416 now (101 hours). He was either lying or the shop ripped him off! Either way, it has new oil and a new filter! Whew. I know I can trust MY work.

The lesson here is that when you buy a used coach, go ahead and have all of the service regardless of what someone tells you.
Fred H.
1996 Foretravel U320 4000 Build #4993 (Previous motorhomes 1985 Airstream 345, 1977 Argosy 20)
Sevierville, TN
ViewRVs.com

Re: Power Tech Generator Oil Change?

Reply #12 –
after 100 hours the oil from our kubota is very black also.......
I use Delo 400 15W-40 and napa gold filter
Justin & Cathy Byrd
1995 U280 "Old Faithful"
36' Build #4673
C8.3 Cummins
Allison MD3060R 6 speed - retarder
Powertech 10KW  4cyl Kubota

Re: Power Tech Generator Oil Change?

Reply #13 –
Agree, diesel oil will be very black.  One reason you need to change by the recommended hours. You would never be able to tell by the oil color.
Steve DeLange
2005 U320T 40'
Pearland, Texas

Re: Power Tech Generator Oil Change?

Reply #14 –
Fred,

While you have the generator slid out you need to change the water pump belt if you have the remote radiator. This is especially needed if you have an Isuzu engine as it is a PITA to try to replace the belt setting in a rest area.

Pamela & Mike
Pamela & Mike 97 U 320

"It's not what happens to you, but how you react to it that matters."

Re: Power Tech Generator Oil Change?

Reply #15 –
Recommended interval for the Isuzu 3 cyl is 50 hours.
96 U270 BUILD 4810
85 380SL
Drummonds TN.

Re: Power Tech Generator Oil Change?

Reply #16 –
Quote from: John44 –
Recommended interval for the Isuzu 3 cyl is 50 hours.
My Powertech manual says to change the oil at 250 hrs.

Mark
The selected media item is not currently available.
Mark and Tanya
Milton , Florida
US Navy Veteran (DV)
1999 U270 Special 40' CAI , 2015 Jeep Wrangler Sahara
 

Re: Power Tech Generator Oil Change?

Reply #17 –
With low sulphur diesel and the better oils that we have today, longer oil change intervals are possible.
Justin & Cathy Byrd
1995 U280 "Old Faithful"
36' Build #4673
C8.3 Cummins
Allison MD3060R 6 speed - retarder
Powertech 10KW  4cyl Kubota