Skip to main content ↑ ↓
Topic: Odd Gen Tray (Read 542 times) previous topic - next topic

Odd Gen Tray

Just got home and ready for the first project.  When trying to find the thump in our gen set I found a badly deteriorated rear mount.  I am going to pull the set and do a mod, Marks MAZ including powdercoat, replace the mounts and isolators, and the insulation as well. 

Reading the other posts I saw that my tray does not have the same pattern as the other 8k 270s.  Should I replace it, bolt plate over it or weld?  Was this pattern found on other trays?

Thanks
George and Steph
1997 U270 36 Build 5081 "Honu"
1180w Solar 400A lithium all Victron house system
Motorcade 17670, SKP 128300, FMCA F459019
73 VW Camper, 79 VW Camper, 2363 Sunline, and an Arctic Fox 25P

Re: Odd Gen Tray

Reply #1 –
Quote from: George and Steph –
  I am going to pull the set and do a mod, Marks MAZ including powdercoat, replace the mounts and isolators, and the insulation as well.

Just curious, what's the story with the two loose wires on the lower right in pic # 1 ?
1993 U-240 "La Villa Grande"..CAT 3116 w/ Pacbrake PRXB...Allison 3060 6-speed..
Previous: 1983 Airstream 310 turbo diesel, 1979 Airstream 280 turbo diesel
                                      Build # 4297
                                      PNW natives
                      Home base:  'Cactus Hug' (Ajo, Arizona)
                        DW Judy & Chet the wonder dog
                        Full-Timers 'Sailing the asphalt sea'

Re: Odd Gen Tray

Reply #2 –
Those are from the resovoir.  It was crimped completely closed with a mudobber attempt on the far end.
George and Steph
1997 U270 36 Build 5081 "Honu"
1180w Solar 400A lithium all Victron house system
Motorcade 17670, SKP 128300, FMCA F459019
73 VW Camper, 79 VW Camper, 2363 Sunline, and an Arctic Fox 25P

Re: Odd Gen Tray

Reply #3 –
That looks like a piece of clear plastic hose too me?? Maybe I do need eyes checked if not??
JohnH
Coachless, now use aircraft. 2003 Ford Travelair TC280 class C. Super shape. Just for 1 yr .
1994 Ford E350 ClassC,total renovation inside and out. Now sold.
2000 U295  36' Cummins 350 c/w Banks Stinger, Resonator upgrade,Solar, LED lites.Residential fridge with slide out pantry. Build 5674. Sold
ex 92 GV 022C ored Cummins. Sold
ex 95 GV240 cat 3116. Sold
2017 Mini cooper s & 2016 land Rover LR2 HSE  LUX.
jhaygarth@aol.com    SKP #130098
treat everyone as you would like to be.

Re: Odd Gen Tray

Reply #4 –
The tray was punched to fit either the  Kubota or Isuzu engine,
The selected media item is not currently available.Bill&Doris 97 U270 36'
University of Parris Island Class of 66
Semper Fi  Build# 5174 MC#17094

Re: Odd Gen Tray

Reply #5 –
Yes it is clear plastic from the resovoir.  The overflow end was crimped shut the other end was blocked with mud.

Bill any good reason to cover those openings?
George and Steph
1997 U270 36 Build 5081 "Honu"
1180w Solar 400A lithium all Victron house system
Motorcade 17670, SKP 128300, FMCA F459019
73 VW Camper, 79 VW Camper, 2363 Sunline, and an Arctic Fox 25P

Re: Odd Gen Tray

Reply #6 –
No.
The selected media item is not currently available.Bill&Doris 97 U270 36'
University of Parris Island Class of 66
Semper Fi  Build# 5174 MC#17094

Re: Odd Gen Tray

Reply #7 –
Your photos look identical to ours.  Not sure what you are concerned about.  We painted generator, tray bottom and top, put new mounts and isolators and new foil over original insulation.  But we did not see any reason to remove generator or tray, as we could just pivot generator about mounts while painting.
Did run into an issue...  found radiator bottom isolator bolts not glued to rubber isolator, which probably allowed radiator to move about a little during engine vibrations.  The 'failed' isolators did not cause any problems and the broken isolator was only found when we replaced them with new ones purchased from Power Tech.  Well a short time later, one day we found the bottom of the radiator had broken its solder joint and leaked coolant.
Determined that the new isolators did not allow the rad to move about and the rad bottom could not take the vibrations, putting more pressure on the soldered end, which may be the weakest part of the radiator.
If we had left the broken isolators in place, we would have been better off.
Our fix was to remove bottom two isolators and support the radiator bottom at its strongest point with new rubber mounts under the tank.  That is, after we had the radiator bottom tube soldered at the leak breaks.
Bottom of gen compartment drops off by removing 4 fasteners, allowing complete access to back of generator from bottom.  Sitting with our upper body behind gen, we did find a very small oil leak at the oil pressure sender, that we did not know about.
 

Re: Odd Gen Tray

Reply #8 –
Thanks for your insight Barry.  Since I am unfamiliar with the need to separate the radiator, I was going to do Marks modification as a preventive project.  My concern, after seeing many of the pictures, was that I may be dealing with a repair or replacement that would require a different approach since the tray was stamped for a different product.
George and Steph
1997 U270 36 Build 5081 "Honu"
1180w Solar 400A lithium all Victron house system
Motorcade 17670, SKP 128300, FMCA F459019
73 VW Camper, 79 VW Camper, 2363 Sunline, and an Arctic Fox 25P