Skip to main content ↑ ↓
Topic: Filter changes (Read 605 times) previous topic - next topic

Filter changes

Getting all of my Oil/filters, coolant sysyem and water separators and anything I have missed changed. Changed 2 engine oil filters and one generator. Also changed one filter next to leveler rear divers side. Looked like transmission fluid. So now do I have to had trans fluid. Filter only held a small amount so don"t know if I should add since it was such a small amount so that is one thing I need advice on

Next up is the fuel filter 3528. Should I fill the filter before I put it back on or use the handpump? Don't want to get myself in a jam here and not be able to eng restarted

Next have a ? Regarding the coolant filter. Can I just change the filter and put new in place with no problem? The fuel filter that sets up on top of eng was changed by mechanic

So are there any filters or water separators that I have missed. Doing the best I can with the forums help. When I make these last updates I hope I am ready for AZ Trip leaving from McMinnville, Or to Sun City West AZ. Approx 1200 miles. New tires, good breaks, no propane leaks, steering seems solid and air pressure system good and all gauges seem to read appropriate. If I have missed anything please let me know
 I have not checked front wheel bearings so I have that to worry about.
Bob and Carol Cox
1987 gv 36 ft dp
Cat 3208t
2013 tundra crew cab lift

Re: Filter changes

Reply #1 –
Someone with your engine will chime in but are you sure the engine has 2 oil filters?If you put in what came out on the trans fluid you
should be good,check with your dipstick.Someone will also chime in about your coolant filter,check if you have a shutoff valve to
use while you change it.Did you change the oil or just filters?Do you have the books,some of this info is there.
96 U270 BUILD 4810
85 380SL
Drummonds TN.

Re: Filter changes

Reply #2 –
Thanks John. Yep 2 oil filters on the 87 cat turbo. Side by side just off center on the passenger side. Was surprised myself. Changed the oil as well. Learning and hoping to tame this cat. Ha ha
Bob and Carol Cox
1987 gv 36 ft dp
Cat 3208t
2013 tundra crew cab lift

Re: Filter changes

Reply #3 –
When we had the FT with a 3208 here is what I can recall 
Don't remember it having an external trans filter but that was long ago and haven't had one in the shop in a long time either.
As far as the fuel filter I put the filter on dry and used the hand pump.
The coolant filter is determined by what kind of antifreeze you have. If old school you will need to test to see how many SCA filter you will need.  If OAT you will need a blank.
The wheel bearings aren't nothing to loose a lot of sleep over. Unless you overtighten them and burn them up they are pretty robust.  Check them over, check end play, new oil, new center red plug and you are good to go.

Pamela & Mike
Pamela & Mike 97 U 320

"It's not what happens to you, but how you react to it that matters."

Re: Filter changes

Reply #4 –
I am planning on replacing the coolant filter with the same number filter that is currently on the system. Hope the last gal or guy used the right one. Time will tell. Lol
Bob and Carol Cox
1987 gv 36 ft dp
Cat 3208t
2013 tundra crew cab lift

Re: Filter changes

Reply #5 –
The only other filter would be the transmission filter that is inside the pan on the transmission. If the oil is bright red then probably does not need to be changed.
previous 1984 35 ft ORED 250 HP 3208 Cat       
previous 1998 40 ft U295 CAI 325 hp Cummins
previous 2003 40 Ft u320 build #6140 450 Cummins M11.                                                         
1999 Mazda Miata
Ron, Nancy, Tipper the cat, Max The dog
1997 U 270 36 ft build number 5174 8.3 Cummins

Re: Filter changes

Reply #6 –
If you are unsure of your engine filters, get your engine serial number and call Cat.
The selected media item is not currently available.Bill&Doris 97 U270 36'
University of Parris Island Class of 66
Semper Fi  Build# 5174 MC#17094

Re: Filter changes

Reply #7 –
Good idea Bill. Thank you
Bob and Carol Cox
1987 gv 36 ft dp
Cat 3208t
2013 tundra crew cab lift

Re: Filter changes

Reply #8 –
Differential oil level check, if there are any signs of leaks. Not hard to check if you can remove the plug. Just stick your finger in there and bend a nukle, if you detect oil your good. Buy an IR temperature gun about $30-40 and the 30 min. driving you can do a walk around shooting tire, axle, brake drum, engine, tranny, radiator etc temperatures. Takes about 5 minutes. As my confidence built i stretched the walk arounds an additional 15 minutes. I would have done the first one at 30 minutes, but i was still in LA proper. Did my first near Riverside where the shoulders we're wider. Now i do two hour walk arounds. Get a bath towel to stuff under the range cover. I drove home with a cooler and all gas appliances shut off. Babyed it for 2 hours until i got to Barstow. Topped the tanks and let her go strut her stuff.
Old Phart Phred, EIEIO
89 GV ored 36' #3405 300 hp cat 3208 ATAAC side radiator, mountain tamer exhaust brake

Re: Filter changes

Reply #9 –
Quote from: Bill Willett –
If you are unsure of your engine filters, get your engine serial number and call Cat.
Good luck with that, my serial number comes up non existent. May just be a typo on my paper documents. IDK.
Old Phart Phred, EIEIO
89 GV ored 36' #3405 300 hp cat 3208 ATAAC side radiator, mountain tamer exhaust brake

Re: Filter changes

Reply #10 –
Can n9t believe the little problems I am coming up with. I was trying to 7nscrew the water fuel separator looks fairly new. Cranked on it with a filter adapter and started to bent the filter and was making the filter attachment move. So moved the filter taker offer up toward the top of filter, same problem. Last guy must have really put it on, tight.

Put penetrating
 oil on top edge of filter and will try in morning. If that far not work guess I can run a large screw driver close to the top and twist it off.

Could take a touch and heat the top so it will expand. Bet that would work! Of course I am kidding. Sometimes a little levity helps
Bob and Carol Cox
1987 gv 36 ft dp
Cat 3208t
2013 tundra crew cab lift

Re: Filter changes

Reply #11 –
I like to put the fuel filter on dry but leave it slightly loose.  Use the hand pump until fuel starts to drip down the outside of the filter.  Tighten the filter and the engine should start right up.
Regards,
Brett

'99 42' Foretravel Xtreme
'14 Brown Motorsports Stacker
'05 Chevy SSR
'02 BMW R1150R

Re: Filter changes

Reply #12 –
Quote from: Old phart phred –
Good luck with that, my serial number comes up non existent. May just be a typo on my paper documents. IDK.
Opp,

Did you compare the paperwork with the serial number that is on the engine it's self?  The one on the engine is the bible.

Mike
Pamela & Mike 97 U 320

"It's not what happens to you, but how you react to it that matters."

Re: Filter changes

Reply #13 –
Quote from: bigfoot –
I am planning on replacing the coolant filter with the same number filter that is currently on the system. Hope the last gal or guy used the right one. Time will tell. Lol

That is often an INCORRECT ANSWER. This is the one place that replacing with the same filter can get you in trouble.

If you are using the old style coolant with SCA your coolant filter is both a filter and a means of adding SCA.  All filters "filter"  Additionally, filters come with units of SCA ranging from zero (filter blank) to 16 units.  Keeping the correct concentration of SCA is important.  So before determining the correct filter, YOU HAVE TO TEST THE COOLANT.

Coolant test strips are available at any shop that works on diesels.  They are easy to use-- dip in and compare colors.  The better ones test for: SCA concentration, freeze point and pH.
Brett Wolfe
EX: 1993 U240
Moderator, ForeForum 2001-
Moderator Diesel RV Club 2002-
Moderator, FMCA Forum 2009-2020
Chairman FMCA Technical Advisory Committee 2011-2020

Re: Filter changes

Reply #14 –
Quote from: amos.harrison –
I like to put the fuel filter on dry but leave it slightly loose.  Use the hand pump until fuel starts to drip down the outside of the filter.  Tighten the filter and the engine should start right up.
Yes, good to have a plastic bag or container and pump until there are no more bubbles. Then tighten 3/4 turn after filter touches housing. Many filters have instructions on the side and marks for each 1/4 all the way around. If they don't, you can use a felt tip marker to put the quarter marks on it.

Pierce
Pierce and Gaylie Stewart
'93 U300/36 WTBI
Detroit 6V-92TA Jake
1140 watts on the roof
SBFD (ret)
 

Re: Filter changes

Reply #15 –
Beam alarm has the oil filter numbers for cat 3208.. I had the filter numbers but gave the folder to the new owner.
Dub McBride 1996 270