Skip to main content ↑ ↓
Topic: 2002 living room slide adjustment (Read 546 times) previous topic - next topic

2002 living room slide adjustment

Hoping someone can help with this problem as FT has not been helpful.  My slide room sits too low in the opening and it is causing the gap at the top to be too large and the gap at the bottom to be too small and also causing the gap at the lower corner radii to be way too tight.  I need to have the seal replaced by my dealer (it was agreed and included in the purchase agreement) and I need to know how this room can be adjusted so it meets the HWH spec for proper gap which they state is nominal 3/8" and maximum 1/2".  My dealer knows nothing about Foretravels and I need to find out how this is done so the new seal does not get damaged.  I know I have the train slide mechanism but it's not clear to me where the weight of the slide room is carried and how it can be adjusted to sit in the opening properly.  I've attached two pictures and one of them is my coach showing the tight corner and the other is a photo I found on line showing the seal replacement process with the slide room pushed in and you can see what appears to be an aluminum bearing surface of some sort.  I'm wondering if there are shims there.  If anyone has any knowledge of these slides or other advice for me it would be greatly appreciated.
George Mann
2002 U320 #5934
2017 Rubicon
2013 BMW GS
Waterford MI

Re: 2002 living room slide adjustment

Reply #1 –
Ping Brad Slaughter via the forum if he doesn't see this first.  He's gotten pretty "up close and personal" with the 2002 slides.
Learn every day, but especially from the experiences of others. It's cheaper!  - John C. Bogle

2000 U320 36' non-slide / WildEBeest Rescue
2003 U320

Re: 2002 living room slide adjustment

Reply #2 –
Yes, the room rides on plastic guides and they can be shimmed.  MOT did mine.  They pushed in the room as shown in pic 2 and shimmed.

You may be able to see them if you deflate the bladder or look from the inside with the room extended.

Rich
Rich and Peggy Bowman
2002 U270 3610 WTFS, build #5939--"Freedom"
2022 Jeep Grand Cherokee Summit 4xe
SMI AirForceOne brake system
PakCanoe 15

Re: 2002 living room slide adjustment

Reply #3 –
2002 U 270 shims are placed under the plastic pad shown in the picture , since I didn't have more shims I actually made a shim to raise the aluminum block to a specific height and then used shims under plastic pad (actually removed the shims under the plastic pad)
John Patrick
2002 U270

Re: 2002 living room slide adjustment

Reply #4 –
The hardest part of this whole job is removing that decorative piece from the slide on the inside that connects both column pillars to the center, I have modified that, Making the posts separate from the centerpiece.
John Patrick
2002 U270

Re: 2002 living room slide adjustment

Reply #5 –
John, those pictures are invaluable, thank you so much.  I now have a pretty good understanding of how the slide functions.  I too have removed the interior slide pieces and separated them.  I added a ledger to the big top header so that I can lift it into place by myself and it will support itself until I can install the button head screws from underneath.  I added metal angle brackets to connect the side trim to the header trim and I can access them with a small screw gun from behind to fasten them together.  Someone before me didn't know how to get all of the trim apart and actually split the cherry wood in several places and glued it back together.  I suspect it was probably an RV repair shop that was not familiar with FT.  Thanks again for the info and pictures.
George Mann
2002 U320 #5934
2017 Rubicon
2013 BMW GS
Waterford MI
 

Re: 2002 living room slide adjustment

Reply #6 –
One other thing that I found out at least in my situation to get the slide to go in the additional 3 inches needed to clear the pads and aluminum block I needed to remove all the bolts that hold the train system to the bulkhead
John Patrick
2002 U270