Skip to main content ↑ ↓
Topic: Aqua hot Squeeking (Read 406 times) previous topic - next topic

Aqua hot Squeeking

As part of wrapping up a fuel system upgrade (FASS), and an entire fuel line replacement I am finally to the point of getting the Aqua hot back up and running, I am sure its been doing this since I bought it, but with the covers off more noticeable. It sounds like I have a light bearing squeek going on when the blower is running. As I have a bit of smell and sooting when running was going to do a service on it while I am at it. Based on the service manual I have there is a bearing Kit for the blower, but I cant find a part number for it anywhere in my manual nor on any AH web links. Has anyone done these bearings before and happen to know the Kit #, and where to acquire. Or just the bearing numbers, looks like the rest of what would be a kit is non wear items.
I have the AHE-100-01S model heater.

Thanks, Mike

https://www.foreforums.com/index.php?action=dlattach;sa=tmpattach;attach=post_tmp_7956_34e9ff1fc8eb704135c0cec128d0e55a;topic=0
Mike in AL
2001 U295
8.3 ISC 350
Build 5918

Re: Aqua hot Squeeking

Reply #1 –
The foretravel link doesn't work for me. Rudy may have the bearing numbers. Ill text you his numbers this morning. Good guy and holds the fastest shipping record for help.
Scott

Re: Aqua hot Squeeking

Reply #4 –
You could take it apart and take the old bearings into a bearing shop and they would
be able to match them up.
Peter and Frieda Morin
1999 36ft. U320 Foretravel
Build # 5436
1998 Suzuki Sidekick Sport

Re: Aqua hot Squeeking

Reply #5 –
Mike,

Here you go 608-2RS 8mmx22mmx7mm don't buy the thriftly made ones for skateboards as you will be disappointed with the results.

Mike
Pamela & Mike 97 U 320

"It's not what happens to you, but how you react to it that matters."

Re: Aqua hot Squeeking

Reply #6 –
Call Rudy,  713 eight one eight  3234

Blower bearings are not very expensive and replacable.  Parts from Rudy come with help as needed.

Blower motors can wear as well, in that case it is an entire motor, no serviceable bearings.  Do the blower bearing first.
Roger Engdahl and Susan Green
2001 U320 3610 #5879 (Home2) - 2014 Jeep Cherokee or 2018 F150
Hastings, MN

Re: Aqua hot Squeeking

Reply #7 –
Thanks for all the feedback folks. as told Scott when he texted me, Im in the middle of plant maintenace shutdown, ( 12hrs 14 days then a break) and barely finding time to research up my parts and post a ? or two on the occasional break. Trying to get as much as possible pre tear down. According to the docs I have the 100_01S does not have much other than a new jet and alot of cleaning. I thought there was a gasket tween the main body and the housing but surely dont see on on the spec sheet. Got some jets/filters coming.

Mike thanks for the number spec on the bearing, I actually keep a few dozens bearings of various sizes in my shop I think I may have a few of those. Yep dont ever skimp on bearings, and from what I have seen in the past 20 years, even on the primo brand, SKS, National, Timken, etc... if you get one that is sealed which an RS is, pop the seals even on a new one and check for grease, it would surprise many out there just how many come with near zero grease.

Roger, Yes I hope its only the bearings, sure sounds like it, imagine the motor is probably only bronze sleeved if non serviceable, bummer

Mike
Mike in AL
2001 U295
8.3 ISC 350
Build 5918

Re: Aqua hot Squeeking

Reply #8 –
I used the 608-2rs  SKF as Mike posted have not had any problems so far
Chris
1999 U 320 DGFE
Build Number 5523
Chris & Elka Lang
In the field, Lonoke AR
 

Re: Aqua hot Squeeking

Reply #9 –
Mike/Chris

Thanks for the reference to the 608-2RS. I had 1 in my stock pile in my shop. Not enough to do this job, so ordered a few more last night along with about a dozen other common sizes I often use around my place. Thanks for that info, that was the sort of info I was looking for.


Mike in AL
2001 U295
8.3 ISC 350
Build 5918