Skip to main content ↑ ↓
Topic: Re: Water Fill Solenoid relay (Read 536 times) previous topic - next topic - Topic derived from Re: Water Fill Soleno...

Re: Water Fill Solenoid relay

Quote from: DavidS –
2-Way Brass Solenoid Valve NBR Seals DIN Gas Air Water Oil Electric Pneumatic...

This might help with a replacement also.

I replaced my water fill valve with a ball valve and haven't been able to test it cause coach is still winterized.  Is that an ok manual substitute?  Took the old valve apart to clean it and hopefully reuse.  Looks like the diaframe has the tiniest of holes in it, the size of the small end of a toothpick. Could this be why it is not working. The solenoid was clicking when the water fill switch was turned on.  Has anyone used the replacement DavidS recommends above?  Found the rebuild kit for $105, doesn't specify what is in the kit.  Will keep searching, thanks for your help and suggestions

2000 GV320 4010 build #5712  2019-?
1999 Bounder 2000-2008
Bardstown, KY
🥃The Bourbon Capital of the World🥃

Re: Re: Water Fill Solenoid relay

Reply #1 –
Quote from: Tommy D –
1.  Looks like the diaframe has the tiniest of holes in it, the size of the small end of a toothpick. Could this be why it is not working.
2. The solenoid was clicking when the water fill switch was turned on.
3. Has anyone used the replacement DavidS recommends above?
4. Found the rebuild kit for $105, doesn't specify what is in the kit. 

1.Yes it could be the problem.
2. This is a good thing.
3. That isn't a pilot valve like OEM but would work
4. Which valve manufacturer do you have. During the time of your coach being built F/T changed valve companies. With this it will determine what is in the rebuild kit.

Mike
Pamela & Mike 97 U 320

"It's not what happens to you, but how you react to it that matters."

Re: Water Fill Solenoid relay

Reply #2 –
This is what I have

I think it is this below but not 100% sure

PARKER HANNIFIN
12F24C2148A3FR

2000 GV320 4010 build #5712  2019-?
1999 Bounder 2000-2008
Bardstown, KY
🥃The Bourbon Capital of the World🥃

Re: Water Fill Solenoid relay

Reply #3 –
That number is correct for that valve, except the "R" is for the rebuild kit.  If you pull the coil off there should be a thin piece of material under it that will give you the valve number. I have posted how to rebuild one of those valve with pics. and will get the link when I find it.  You can get the rebuild kits for a little less than what you have found just shop around.

That valve is to notch and most of the time the valve will fail due to trash in the pilot valve orifice or a failed diaphragm.

Mike
Pamela & Mike 97 U 320

"It's not what happens to you, but how you react to it that matters."

Re: Water Fill Solenoid relay

Reply #4 –
Here you go look this over if you have any questions give a shout.
Water Fill Valve Issues

Mike
Pamela & Mike 97 U 320

"It's not what happens to you, but how you react to it that matters."

Re: Water Fill Solenoid relay

Reply #5 –
Mike
will ball valve work as a manual substitute?

Thanks for your input!

2000 GV320 4010 build #5712  2019-?
1999 Bounder 2000-2008
Bardstown, KY
🥃The Bourbon Capital of the World🥃
 

Re: Re: Water Fill Solenoid relay

Reply #6 –
Quote from: Tommy D –
will ball valve work as a manual substitute?

Yes
The down side is you will most likely not  have good access to it's location. Other than that a ball valve will work just fine. There are a lot of F/T coaches that have manual ball valves for fill valves. It is the KISS system.

Mike
Pamela & Mike 97 U 320

"It's not what happens to you, but how you react to it that matters."