Skip to main content ↑ ↓
Topic: Basler AVC63-4 Gen-set regulator (Read 235 times) previous topic - next topic

Basler AVC63-4 Gen-set regulator

Just replaced my bad Gen-Set regulator (Basler AVC63-4) on the PowerTech 10KW unit. I have only 96Volts at the meter on my panel.  I see on the back of this regulator there are 3 Potentiometer's. Would these be the way adjust this? Or is a field flash needed?
Jerry & Nona and Kimeru the cat that thinks she's a dog
1998 36' WTFE U320  #5314 Motorcade #17711
USAF 1975-1995
2019 Subaru Crosstrek 'toad'
2003 Subaru Legacy touring car
jerry Fincher | Flickr

Re: Basler AVC63-4 Gen-set regulator

Reply #1 –
Tweak the potentiometer. Very small adjustments will make significant changes in the output voltage. Easiest if you have someone watching the voltages while you make changes.

Re: Basler AVC63-4 Gen-set regulator

Reply #2 –
Quote from: Bob McGee –
Tweak the potentiometer. Very small adjustments will make significant changes in the output voltage. Easiest if you have someone watching the voltages while you make changes.
That worked. Ran it no load to 120V. When given a full load it was at 116V.  I don't have a Freq. meter to measure that setting.
Jerry & Nona and Kimeru the cat that thinks she's a dog
1998 36' WTFE U320  #5314 Motorcade #17711
USAF 1975-1995
2019 Subaru Crosstrek 'toad'
2003 Subaru Legacy touring car
jerry Fincher | Flickr

Re: Basler AVC63-4 Gen-set regulator

Reply #3 –
You need to set it to 60 cycles or damage may occur.
1999 40 ft. U-320 wtfe build 5563 Chuck & Lynda's "Rollin' Inn"  2030 watts solar
prev. mh's 71 GMC 5 yrs. 73 Pace Setter 1 yr. 78 Vogue 5 yrs 81 FTX 40ft all electric 18 yrs. 1996 Monaco Signature 3 yrs.
2014 Grand Cherokee Overland
Dream as if you will live forever. Live as if you will die today.  James Dean

Re: Basler AVC63-4 Gen-set regulator

Reply #4 –
Quote from: craneman –
You need to set it to 60 cycles or damage may occur.

Of course that begs the question as to how to set the frequency. I take it that is done with the engine rpm? If so, The frequency was right at 60HZ when the tech tested the regulator.
Jerry & Nona and Kimeru the cat that thinks she's a dog
1998 36' WTFE U320  #5314 Motorcade #17711
USAF 1975-1995
2019 Subaru Crosstrek 'toad'
2003 Subaru Legacy touring car
jerry Fincher | Flickr

Re: Basler AVC63-4 Gen-set regulator

Reply #5 –
I think the Rpm should be 1800 so if you have a Tach you can set your cycle correctly.
Peter and Frieda Morin
1999 36ft. U320 Foretravel
Build # 5436
1998 Suzuki Sidekick Sport

Re: Basler AVC63-4 Gen-set regulator

Reply #6 –
Quote from: oldguy –
I think the Rpm should be 1800 so if you have a Tach you can set your cycle correctly.
No tach on the gen.  I'm pretty sure I'm fine as the frequency was fine a couple of weeks ago. But I will buy a freq meter, just to verify before I use the gen again.
Jerry & Nona and Kimeru the cat that thinks she's a dog
1998 36' WTFE U320  #5314 Motorcade #17711
USAF 1975-1995
2019 Subaru Crosstrek 'toad'
2003 Subaru Legacy touring car
jerry Fincher | Flickr
 

Re: Basler AVC63-4 Gen-set regulator

Reply #7 –
If you have not tinkered with the governor setting 1800 rpm the cycles will be ok.
Bruce, Linda, and Macy
Zoey RIP 1/20/19
1999 U295 40' build #5400
2017 silver Jeep Wrangler, 1260 watts of solar on top
Moving around the country