Skip to main content ↑ ↓
Topic: Genset Exhaust Gasket (Read 557 times) previous topic - next topic

Genset Exhaust Gasket

Does anyone have a generic part number for the genset exhaust flange gasket (the one where the exhaust pipe connects to the flexible pipe leading to the muffler) on a Power Tech 10KW?

Re: Genset Exhaust Gasket

Reply #1 –
Don't have a number, but Powertech will have the part.
Richard & Betty Bark & Keiko our Golden Doodle
2003 U320T 3820 PBDS
Build # 6215
MC # 16926
2016 Chevrolet Colorado 4X4 diesel

Re: Genset Exhaust Gasket

Reply #3 –
If it's a flat gasket, you can make/cut your own
Old Phart Phred, EIEIO
89 GV ored 36' #3405 300 hp cat 3208 ATAAC side radiator, mountain tamer exhaust brake

Re: Genset Exhaust Gasket

Reply #5 –
The exhaust gasket material will run about $14.00 for 10" X 10".  I should be able to match one up at a local parts store for $5.00.
I say "should" because nowadays they can't even talk to you without knowing what kind of car.
Longing for the good old days.

Re: Genset Exhaust Gasket

Reply #6 –
Just make sure the material Ohis for high heat. Maybe can find a matalic covered gasket material..
Richard & Betty Bark & Keiko our Golden Doodle
2003 U320T 3820 PBDS
Build # 6215
MC # 16926
2016 Chevrolet Colorado 4X4 diesel

Re: Genset Exhaust Gasket

Reply #7 –
Quote from: Travelin' Man –

I say "should" because nowadays they can't even talk to you without knowing what kind of car.
Longing for the good old days.

Boy ain't that the truth
'02 40' U320t  4010WTFS Build 6036 1 slide
Motorcade # 17841
SKP 151920
Retired truck driver
 5 million miler
Still have itchy feet for travel

Re: Genset Exhaust Gasket

Reply #8 –
Rbark is 100% right, you will need a high temp gasket with either metal on the outside (both sides) or in the middle.  The type with metal (perforated) sandwiched in the middle is preferred as the softer material will seal at lower bolt loads than metal.  The reason for the metal is even though it will be between bolted flanges there is still movement.  The preferred method would be to take the flange or a pattern to a gasket shop in your town or close by and get one made. Should not be any thicker than 1/16" (check the condition of the flange, for warpage or extensive pitting).  The gasket shop probably will not even charge you for it as it will only take a minute to make.  If you want call me and I can answer any questions you may have.  Have had 20 years owning a gasket and mechanical manufacturing company.
John...713.907.4311
John and Stacey Smith
Motorcade NO: 11973
1997 U295 CSGI 40'..Build No. 5036     
920 Watts on the roof..CAT Power w/fuel Inj. Programmer
2021 GMC Sierra AT4 1500
EX..2015 Jeep Wrangler Sahara
Ex 1990 U280 RSAI 36'..Build No. 3638

Re: Genset Exhaust Gasket

Reply #9 –
Some of the old time auto parts shops have a rack with hooks and exhaust gaskets hanging on them. I would make a cardboard template up and take it in and see if they can match it up. Mine is 1 1/2 pipe O.D.
Jim C.
coachfree, previous 1997, 1999, 2000, and 2003 Foretravels.

Re: Genset Exhaust Gasket

Reply #10 –
If you have the Kabota 4 cylinder,make a template and go to a Kabota tractor dealer.
The selected media item is not currently available.Bill&Doris 97 U270 36'
University of Parris Island Class of 66
Semper Fi  Build# 5174 MC#17094

Re: Genset Exhaust Gasket

Reply #11 –
Update.

Apparently the gasket is only available from FT as per Powertech and I have been unable to locate a generic replacement,
so I now have a call in to FT.

Re: Genset Exhaust Gasket

Reply #12 –
Check the Power Tech parts page, they list a gasket for the kubota  engine for $8.40.
The selected media item is not currently available.Bill&Doris 97 U270 36'
University of Parris Island Class of 66
Semper Fi  Build# 5174 MC#17094

Re: Genset Exhaust Gasket

Reply #13 –
Bill, I saw that too, but the guy that spoke with me said they sell nothing that's not pictured in the drawings.

Anyway, FT has them for $2.34 each.  I bought two of them (one for insurance) and they're coming in a standard envelope
for .50 at my request.  I hoping both don't get broken so I'll at least have one good one when they arrive.  If I have an extra someone here can have it.

FT Part # P56248