Skip to main content ↑ ↓
Topic: Remove holding tanks  (Read 588 times) previous topic - next topic

Remove holding tanks

Can anyone out there tell me how to remove the holding tanks and the water lines ,the water line looks like you need a special crimping tool and the tanks look like you knock out the white fibreglass spacers underneath the tanks and the tanks would drop down so that the drain of washer and toilet and shower would clear the tanks. Or am I way off on this one.
Rick & Hilda looking forward to full- timing one day for now couple of months at a time
1999 U270 3602
Built number  5530.  Feb 1999            Motorcade  number 18438
8.3 Cummins Allison six speed with brake  retarder
Purchased Nov 28 2019

Re: Remove holding tanks

Reply #1 –
look up sept 16 2017 post by chebuhar.

title is black water tank removal. its in foretravel tech talk


i posted in it to pull it to front
1999 U270 40 #5518
USN. USPS.

Re: Remove holding tanks

Reply #2 –
The fiberglass platforms that the tanks sit on are tapered towards the outlets. You have to remove the maniblock water manifold mounting screws and pull it out of the way. Pull out the fiberglass platforms after removing the caulking around the bottom edges and any screws that might be there. Pull out the fiberglass platforms after removing the caulking around the bottom edges and any screws that might be there. Then the tanks can drop down low enough to clear the vent and inlet pipes, which are in rubber grommets through the top of the tanks. I will try and find a picture that shows the tanks sitting on the fiberglass platforms. You can see the wedge shape.
Don
Quote from: Cape Bretoner –
Can anyone out there tell me how to remove the holding tanks and the water lines ,the water line looks like you need a special crimping tool and the tanks look like you knock out the white fibreglass spacers underneath the tanks and the tanks would drop down so that the drain of washer and toilet and shower would clear the tanks. Or am I way off on this one.
The selected media item is not currently available.
Don & Tys
1999 U270 3602 WTFE #5402
Xtreme Stage 1 w/Headlight, Step Conversion, etc.
2009 Honda Fit Sport with Navi
Freedom is NOT "just another word for nothing left to lose"... with apologies to Kris Kristofferson

Re: Remove holding tanks

Reply #3 –
Thanks don it starting to make sense I'm following your plans and instructions to the tee . This is all new to me  I have the certified welding but taking apart is all new. I have the manifold already of and started on hot water tank will see what tomorrow brings thank again Rick
Rick & Hilda looking forward to full- timing one day for now couple of months at a time
1999 U270 3602
Built number  5530.  Feb 1999            Motorcade  number 18438
8.3 Cummins Allison six speed with brake  retarder
Purchased Nov 28 2019

Re: Remove holding tanks

Reply #4 –
Rick,

Here is the thread Texhub is referring to
Black Water Tank Removal

Pamela & Mike
Pamela & Mike 97 U 320

"It's not what happens to you, but how you react to it that matters."

Re: Remove holding tanks

Reply #5 –
How were you able to do that. He asked me for info. I commenced searching. Thru many loops I finally stumble on that link. I sent it to him via text msg. He was unable to open it as he was on iPad. With fourm. So I then tried to put a link as you did. Was unable due to lack of operator knowledge on fourm.
So I went to the old link and posted in it to pull it to front of fourm. Then told him.

Open to training!  Thanks
1999 U270 40 #5518
USN. USPS.

Re: Remove holding tanks

Reply #6 –
Here's a bunch of photos of when I removed the tanks from our 95. They might be useful. I was not able to pull either tank down off the pipes and had to cut the rubber grommets. Thry are pricey so I hope you have better luck with them. Also, I replaced my black tank with one with slightly different dimensions so I had to fabricate a new cradle for it. It's not a real hard job so I think you will manage it without problems. Good luck.
jor
93 225
95 300
97 270
99 320

Re: Remove holding tanks

Reply #7 –
Thank you for the pictures and the help
Rick & Hilda looking forward to full- timing one day for now couple of months at a time
1999 U270 3602
Built number  5530.  Feb 1999            Motorcade  number 18438
8.3 Cummins Allison six speed with brake  retarder
Purchased Nov 28 2019
 

Re: Remove holding tanks

Reply #8 –
Quote from: Cape Bretoner –
the water lines ,the water line looks like you need a special crimping tool

Rick,

With you having a '99 your Water piping will be standard 1/2" PXE tubing. I prefer copper rings that require a crimping tool.  You can get a simple crimper for a few $ up to a high $$ one. The choice is yours and how much you will be using this tool.  Others use the stainless steel squeeze crimps and have success with those.  Others forgo crimping and use "SharkBite" press fittings. These press fittings are convenient but won't work in all applications.

Mike
Pamela & Mike 97 U 320

"It's not what happens to you, but how you react to it that matters."